About this opportunity
M&D Mechanical Contractors lists this Pipe Welder opportunity in decatur, Alabama. Review the employer’s description below for duties, qualifications and application requirements.
Job description
Job Purpose
Use hand-welding or flame-cutting equipment to weld or join metal components (pipe) or to fill holes, indentations, or seams of fabricated metal products.
WELD TEST REQUIREMENTS
IN 6G POSITION:
6" SCH 40 SMAW
2" SCH 80 CARBON TIG
2" STAINLESS SCH 40
NO PER DIEM OR RELOCATION AVAILABLE FOR THIS POSITION. SUCCESSFUL CANDIDATE WILL RESIDE WITHIN 60-MILES OF DECATUR, AL.
TOP OUT JOURNEYMAN BASE RATE - $32.00/HR +$2.00 SITE SPECIFIC PAY (FBI/MSIC- ONLY)(RATE DEPENDENT ON BENEFIT ELECTION)
Essential Duties and/or Responsibilities
Operate safety equipment and use safe work habits.
Weld components in flat, vertical, or overhead positions.
Ignite torches or start power supplies and strike arcs by touching electrodes to metals being welded, completing electrical circuits.
Clamp, hold, tack-weld, heat-bend, grind or bolt component parts to obtain required configurations and positions for welding.
Detect faulty operation of equipment or defective materials and notify supervisors.
Operate manual or semi-automatic welding equipment to fuse metal segments, using processes such as gas tungsten arc, gas metal arc, flux-cored arc, plasma arc, shielded metal arc, resistance welding, and submerged arc welding.
Monitor the fitting, burning, and welding processes to avoid overheating of parts or warping, shrinking, distortion, or expansion of material.
Examine workpieces for defects and measure workpieces with straightedges or templates to ensure conformance with specifications.
Recognize, set up, and operate hand and power tools common to the welding trade, such as shielded metal arc and gas metal arc welding equipment.
Lay out, position, align, and secure parts and assemblies prior to assembly, using straightedges, combination squares, calipers, and rulers.
Chip or grind off excess weld, slag, or spatter, using hand scrapers or power chippers, portable grinders, or arc-cutting equipment.
Analyze engineering drawings, blueprints, specifications, sketches, work orders, and material safety data sheets to plan layout, assembly, and welding operations.
Connect and turn regulator valves to activate and adjust gas flow and pressure so that desired flames are obtained.
Weld separately or in combination, using aluminum, stainless steel, cast iron, and other alloys.
Determine required equipment and welding methods, applying knowledge of metallurgy, geometry, and welding techniques.
Mark or tag material with proper job number, piece marks, and other identifying marks as required.
Prepare all material surfaces to be welded, ensuring that there is no loose or thick scale, slag, rust, moisture, grease, or other foreign matter.
Select and install torches, torch tips, filler rods, and flux, according to welding chart specifications or types and thicknesses of metals.
Remove rough spots from workpieces, using portable grinders, hand files, or scrapers.
Position and secure workpieces, using hoists, cranes, wire, and banding machines or hand tools.
Clean or degrease parts, using wire brushes, portable grinders, or chemical baths.
Repair products by dismantling, straightening, reshaping, and reassembling parts, using cutting torches, straightening presses, and hand tools.
Fill holes, and increase the size of metal parts.
Dismantle metal assemblies or cut scrap metal, using thermal-cutting equipment such as flame-cutting torches or plasma-arc equipment.
Qualifications
Must pass a weld test. Knowledge and Skills Required:
Mechanical - Knowledge of machines and tools, including their designs, uses, repair, and maintenance.
Equipment Selection - Determining the kind of tools and equipment needed to do a job.
Time Management - Managing one's own time and the time of others.
Worksite address
decatur, AL, 35609, US
Who can apply
Review the original listing for work authorization, qualifications and employer requirements.